| A | B | C | D | E | F | MIN.BURST | ||
| ALLIANCE | ALTERNATIVE | +0.13 | +0.10 | +0.10 | +0.25 | +0.10 | +0.20 | PRESSURE |
| REFERENCE | REFERENCE | -0.00 | -0.10 | -0.10 | -0.00 | -0.10 | -0.20 | (BAR) |
| A201 | PPM3.5 | 7.20 | 5.20 | 4.10 | - | 1600 | ||
| A202 | PPM4 | 7.00 | 5.40 | 4.50 | 3.40 | 1250 | ||
| A203 | PPM5 | 9.00 | 6.80 | 5.70 | 4.50 | 1400 | ||
| A204 | PPM5 | 10.00 | 7.40 | 5.70 | 4.50 | 1500 | ||
| A205 | PPM5.5 | 9.20 | 7.20 | 6.20 | 4.70 | 1220 | ||
| A206 | PPM6 | 10.00 | 8.00 | 6.70 | 0.30 | 1.00 | 4.70 | 1130 |
| A207 | PPM6 | 11.00 | 8.20 | 6.70 | 4.70 | 1510 | ||
| A212 | PPM8 | 13.00 | 10.00 | 8.70 | 6.40 | 1330 | ||
| A213 | PPM8 | 14.00 | 10.40 | 8.70 | 1.00 | 6.40 | 1550 | |
| A215 | PPM8.5 | 13.30 | 10.50 | 9.30 | 6.90 | 1200 | ||
| A216 | PPM10 | 15.88 | 12.00 | 10.35 | 2.00 | 8.56 | 1450 | |
| A217 | PPM10 | 16.00 | 12.40 | 10.70 | 8.05 | 1350 | ||
| A218 | PPM10 | 18.00 | 12.40 | 10.70 | 8.05 | 1880 | ||
| A219 | PPM11 | 16.30 | 12.70 | 11.40 | 9.80 | 1250 | ||
| A221 | PPM11 | 19.10 | 13.50 | 11.80 | 9.80 | 1770 | ||
| A222 | PPM12 | 18.00 | 14.30 | 12.70 | 9.73 | 1250 | ||
| A223 | PPM12 | 20.00 | 14.40 | 12.70 | 9.73 | 1680 | ||
| A225 | PPM13 | 22.00 | 15.40 | 13.70 | 10.80 | 1810 | ||
| A226 | PPM13.5 | 18.70 | 15.70 | 14.00 | 0.40 | 1.50 | 11.30 | 900 |
| A227 | PPM14 | 22.00 | 16.40 | 14.70 | 11.38 | 1510 | ||
| A229 | PPM16 | 24.00 | 18.40 | 16.70 | 13.41 | 1400 | ||
| A230 | PPM17 | 24.00 | 19.20 | 17.40 | 13.08 | 1150 | ||
| A231 | PPM17.5 | 24.70 | 20.10 | 18.00 | 13.60 | 1070 | ||
| A232 | PPM18 | 26.00 | 20.40 | 18.70 | 14.76 | 1275 | ||
| A233 | PPM20 | 28.00 | 22.50 | 20.70 | 16.76 | 1150 | ||
| A234 | PPM21 | 28.70 | 23.30 | 21.50 | 2.50 | 17.80 | 1080 | |
| A236 | PPM22 | 30.00 | 24.40 | 22.70 | 18.74 | 1100 | ||
| A238 | PPM24 | 32.00 | 26.40 | 24.70 | 20.11 | 1050 | ||
| A239 | PPM26 | 35.00 | 28.40 | 26.70 | 22.30 | 1050 | ||
| A240 | PPM27 | 36.00 | 29.00 | 27.20 | 0.40 | 2.00 | 23.30 | 1130 |
| A242 | PPM30 | 39.00 | 33.00 | 31.00 | 25.70 | 860 | ||
| A243 | PPM33 | 42.00 | 35.80 | 33.70 | 28.70 | 900 | ||
| A244 | PPM33 | 46.00 | 36.40 | 34.30 | 28.70 | 880 | ||
| A245 | PPM36 | 46.00 | 38.80 | 36.70 | 31.10 | 880 | ||
| A246 | PPM39 | 51.00 | 41.90 | 40.00 | 2.50 | 34.10 | 1020 | |
| A248 | PPM42 | 53.00 | 44.40 | 42.70 | 3.00 | 36.50 | 940 | |
| A248 | PPM48 | 59.00 | 50.80 | 48.70 | 41.90 | 800 | ||
| A254 | PPM88 | 101.35 | 92.10 | 89.09 | 3.25 | - | 510 |
Standard Design
Self-centralising Design
KEY FEATURES OF SELF-CENTRALISING:
- Elimination of seal offset
- Elimination of leaks
- Ease of installation
- Reduced assembly time
- Captive assembly
TORQUE LOADING
Satisfactory performance of the seal depends on correct torque loading during assembly. The table indicates recommended figures.
For double sealing, additional torque is generally required.
| THREAD SIZE | TORQUE REQUIRED | DOUBLE SEALING FACTOR | |||
| THREAD | BOLT | BSP | Nm | lbf.in | |
| Up to 8 | 5/16 | - | 5.3 | 47+/-3 | 1.6 |
| 10 | 3/8 | 1/8 | 7.1 | 63+/-3 | |
| 11 | 7/16 | - | 11.8 | 105+/-5 | |
| 12 | 1/2 | 1/4 | 15.8 | 140+/-5 | |
| 14 | 9/16 | - | 22.6 | 200+/-10 | 1.3 |
| 16 | 5/8 | 3/8 | 30.5 | 270+/-12 | |
| 18 | 3/4 | - | 40.7 | 360+/-15 | |
| 20 | 13/16 | 1/2 | 56.5 | 500+/-25 | 1.2 |
| 22 | 7/8 | 5/8 | 67.8 | 600+/-30 | 1.1 |
| 24 | 1.0 | 3/4 | 73.4 | 650+/-30 | 1.0 |
| 27+ | 1.1/16 | - | 79.0 | 700+/-35 | |